Connection cable compatible with all our BLDC motors.

Idle speed up to 5483 rpm Max torque up to 1.5 Nm Rated torque 0.2 Nm Rated speed up to 4437 rpm Features BLDC motor t-Rex 3200 I-44-47-L41 S2 14-pole BLDC motor with high-performance neodymium magnets and three digital Hall sensors to detect the rotor position. The electrical connections are designed as a plug-in system. Additional power electronics are required to operate the motor. Motor design with a hollow shaft is also available upon request. This allows the cables to run through the motor or the implementation of output on both sides. Special features BLDC motor 24V l digital l Ø 44mm Designed with focus on rotational speed Enormous performance density – 3 times stronger than motors of comparable size High overload resistance Ideally suited as direct drive, or generator for gearless applications   Technical specifications BLDC motor 24V l digital l Ø 44mm t-Rex 3200 I-44-47 L41 S2 DH 3200.00-3000 Rated voltage 24 VDC 36 VDC 48 VDC Rated current 2,6A 2,6 A 2,8 A Rated torque 0,3 Nm 0,2 Nm 0,2 Nm Rated speed 2000 1/min 3187 1/min 4437 1/min Shaft power (output) 42 W 67 W 93W Max. efficiency 70 % 72 % 72 % Idle speed 2702 1/min 4089 1/min 5483 1/min No-load current 0,4 A 0,4 A 0,4 A Stall torque 1,0 Nm 1,3 Nm 1,5 Nm Starting current at idle speed 14 A 18 A 20 A Torque constant 0,077 Nm/A 0,073 Nm/A 0,073 Nm/A Speed constant 113 rqm/V 114 rqm/V 114 rqm/V Motor parameters Terminal resistance (phase to phase) 1,09 Ohm Terminal inductance (phase to phase) 98 µH Rotor inertia 125 kg* mm² Number of poles 14 Interconnection of the motor Star Number of coils per phase 2 Interconnection of coils 2 Series Direction of rotation bidirectional Note: Max. Ambient temperature = 40°C, controller-specific At nominal point (Tu=20°C) controller specific Digital Hall-sensorsSupply of sensorsVoltage range: 4.5 to 5.5 V DCOptional: voltage regulator for 5 VInput current: < 70 mA Output signals of sensorsDiff erential output(RS422 standard, datasheet AM26 C31-TI)Typical voltage range: 0.2/ 3.4 V @ 20 mAOutput current: max. 20 mA Signal structure: The Hall sensors have a 120°phase shift to each otherDue to the 14-pole design theSignal frequency is seven times higher than the speed

Idle speed up to 1653 rpm Max torque up to 2.9 Nm Rated torque 0.5 Nm Rated speed up to 1347 1/min Features BLDC motor t-Rex 3200 I-44-89-L41 S2 14-pole BLDC motor with high-performance neodymium magnets and three digital Hall sensors to detect the rotor position. The electrical connections are designed as a plug-in system. Additional power electronics are required to operate the motor. The design of the motor with a hollow shaft allows the cables to run through the motor or output on both sides.   Special features BLDC motor 24V l digital l Ø 44mm Designed withfocus on max. torque Enormous performance density – 3 times stronger than motors of comparable size High overload resistance Ideally suited as direct drive, or generator for gearless applications Technical specifications BLDC motor 24V l digital l Ø 44mm t-Rex 3200 I-44-89 L41 S2 3200.00-0005 /3200.00-0006 Rated voltage 24 VDC 36 VDC 48 VDC Rated current 1,7 A 1,8 A 1,7 A Rated torque 0,5 Nm 0,5 Nm 0,5 Nm Rated speed 600 1/min 960 1/min 1347 1/min Shaft power (output) 31 W 50 W 70 W Max. efficiency 83 % 83 % 83 % Idle speed 812 1/min 1221 1/min 1653 1/min No-load current 0,3 A 0,2 A 0,2 A Stall torque 1,8 Nm 2,3 Nm 2,9 Nm Starting current at idle speed 6,6 A 8,7 A 11,2 A Torque constant 0,279 Nm/A 0,264 Nm/A 0,261 Nm/A Speed constant 34 rqm/V 34 rqm/V 34 rqm/V Motor parameters Terminal resistance (phase to phase) 2,6 Ohm Terminal inductance (phase to phase) 1,6 mH Rotor inertia 26,5 kg* mm² Number of poles 14 Interconnection of the motor Star Number of coils per phase 2 Interconnection of coils 2 Serie Direction of rotation bidirectional Note: Max. ambient temperature = 40 °C, controller-specificAt the nominal point (TU = 20°C), controller-specific Digital Hall-SensorsSupply of sensors: Voltage range: 4.5 to 5.5 V DC, Optional: voltage regulator for 5 V, Input current: < 70 mAOutput signals of sensors: Differential output, (RS422 standard, datasheet AM26 C31-TI)Typical voltage range: 0.2/ 3.4 V @ 20 mA / Output current: max. 20 mASignal structure:The Hall sensors have a 120° phase shift to each other. Due to the 14-pole design theSignal frequency: Is seven times higher than the speed

Idle speed up to 4053 1/minMax torque 2 NmRated torque up to 0.3 NmRated speed up to 3767 1/minFeatures BLDC motor t-Rex 3200 I-44-89-L12 S2 14-pole BLDC motor with high-performance neodymium magnets and three digital Hall sensors for detecting the rotor position. The electrical connections are designed as a plug-in system. Additional power electronics are required to operate the motor. A motor version with hollow shaft is also available on request. This makes it possible to feed the cables through the motor or to realize a double-sided output.  Special features BLDC-Motor 24V l digital l Ø 44mm Developed with focus on speed Enormous power density - 3 times more powerful than motors of comparable size High overload resistance Best suited as direct drive or as generator for gearless applications Technical specifications BLDC-Motor 24V l digital l Ø 44mm t-Rex 3200 I-44-89 L12 S2 DH 3200.00-0004 Rated voltage 24 VDC 36VDC Rated current 4,0A 4,0 A Rated torque 0,3 Nm 0,2 Nm Rated speed 2418 1/min 3767 1/min Shaft power (output) 67 W 79 W Max. efficiency 74 % 76 % Idle speed 2680 1/min 4053 1/min No-load current 0,55 A 0,56 A Stall torque 2 Nm 2 Nm Starting current at idle speed 22,7A 21,6 A Torque constant 0,09 Nm/A 0,09 Nm/A Speed constant 112rqm/V 113rqm/V Motor parameters Terminal resistance (phase to phase) 27 Ohm Terminal inductance (phase to phase) 45 mH Rotor inertia 26,5kg* mm² Number of poles 14 Interconnection of the motor Star Number of coils per phase 2 Interconnection of coils 2 Series Direction of rotation bidirectional  Note: Max. ambient temperature = 40 °C, controller-specificAt the nominal point (TU = 20°C), controller-specific Digitale Hall-SensorenSupply of sensors: Voltage range: 4.5 to 5.5 V DC, Optional: voltage regulator for 5 V, Input current: < 70 mAOutput signals of sensors: Diff erential output (RS422 standard, datasheet AM26 C31-TI)Typical voltage range: 0.2/ 3.4 V @ 20 mA, Output current: max. 20 mASignal structure: The Hall sensors have a 120° phase shift to each other. Due to the 14-pole design theSignal frequency is seven times higher than the speed

Idle speed up to 6054 rpmMax. Torque 1.9 NmRated torque 0.6 NmRated speed up to 4812 1/minFeatures BLDC motor t-Rex 3206 I65-51 L36 S2 DH 14-pole BLDC motor with high-performance neodymium magnets and three digital Hall sensors to detect the rotor position. The electrical connections are designed as a plug-in system. Additional power electronics are required to operate the motor. The design of the motor with a hollow shaft allows the cables to run through the motor or output on both sides.   Special features BLDC motor 24V l digital l Ø 65mm Designed with  focus on rotational speed Enormous performance density – 3 times stronger than motors of comparable size High overload resistance Ideally suited as direct drive, or generator for gearless applications Technical specifications BLDC motor 24V l digital l Ø 65mm t-Rex 3200 I-44-89 L41 S2 3206.00-1000 Rated voltage 24 VDC 36 VDC 48 VDC Rated current 7,3 A 5,6 A 1,7 A Rated torque 0,6 Nm 0,6 Nm 0,6 Nm Rated speed 2139 1/min 3208 1/min 4812 1/min Shaft power (output) 134 W 201 W 301 W Max. efficiency 76 % 77 % 77 % Idle speed 2680 1/min 4053 1/min 6054 1/min No-load current 0,5 A 0,6 A 0,6 A Stall torque 1,9 Nm 1,9 Nm 1,9 Nm Starting current at idle speed 20 A 20 A 20 A Torque constant 0,094 Nm/A 0,094 Nm/A 0,094 Nm/A Speed constant 112 rqm/V 112 rqm/V 126 rqm/V Motor parameters Terminal resistance (phase to phase) 0,348 Ohm Terminal inductance (phase to phase) 0,36 mH Rotor inertia 65 kg* mm² Number of poles 14 Interconnection of the motor Star Number of coils per phase 2 Interconnection of coils 2 Serie Direction of rotation bidirectional Note: Max. ambient temperature = 40 °C, controller-specificAt the nominal point (TU = 20°C), controller-specific Digital Hall-SensorsSupply of sensors: Voltage range: 4.5 to 5.5 V DC, Optional: voltage regulator for 5 V, Input current: < 70 mAOutput signals of sensors: Differential output, (RS422 standard, datasheet AM26 C31-TI)Typical voltage range: 0.2/ 3.4 V @ 20 mA / Output current: max. 20 mASignal structure:The Hall sensors have a 120° phase shift to each other. Due to the 14-pole design theSignal frequency: Is seven times higher than the speed

Idle speed up to 1390 1/min Max. Torque up to 9 Nm Rated torque 1.9Nm Rated speed up to 1185 1/min Features BLDC motor t-Rex 3206 I-65-86-L36 S2 14-pole BLDC motor with high-performance neodymium magnets and three digital Hall sensors to detect the rotor position. The electrical connections are designed as a plug-in system. Additional power electronics are required to operate the motor. The design of the motor with a hollow shaft allows the cables to run through the motor or output on both sides. Special features BLDC motor 24V l digital l Ø 65mm Designed with focus on max. torque Enormous performance density – 3 times stronger than motors of comparable size High overload resistance Ideally suited as direct drive, or generator for gearless applications Technical specifications BLDC motor 24V l digital l Ø 65mm t-Rex 3206 I-65-86 L36 S2 DH 3206.00-0005 /3206.00-0003 Rated voltage 24 VDC 36 VDC 48 VDC Rated current 5,4 A 5,6 A 5,6 A Rated torque 1,9 Nm 1,9 Nm 1,9 Nm Rated speed 535 1/min 865 1/min 1185 1/min Shaft power (output) 106 W 167 W 232 W Max. efficiency 84 % 82 % 83 % Idle speed 702 1/min 1052 1/min 1390 1/min No-load current 0,45 A 0,43 A 0,43 A Stall torque 8 Nm 9 Nm 9 Nm Starting current at idle speed 27 A 28 A 26,5 A Torque constant 0,308 Nm/A 0,330 Nm/A 0,343 Nm/A Speed constant 29 rqm/V 29 rqm/V 29 rqm/V Motor parameters Terminal resistance (phase to phase) 121 Ohm Terminal inductance (phase to phase) 0,9 mH Rotor inertia 104 kg* mm² Number of poles 14 Interconnection of the motor Stern Number of coils per phase 2 Interconnection of coils 2 Serie Direction of rotation bidirektional Note: Max. ambient temperature = 40 °C, controller-specificAt the nominal point (TU = 20°C), controller-specific Digital Hall-SensorsSupply of sensors: Voltage range: 4.5 to 5.5 V DC, Optional: voltage regulator for 5 V, Input current: < 70 mAOutput signals of sensors: Differential output, (RS422 standard, datasheet AM26 C31-TI)Typical voltage range: 0.2/ 3.4 V @ 20 mA / Output current: max. 20 mASignal structure:The Hall sensors have a 120° phase shift to each other. Due to the 14-pole design theSignal frequency: Is seven times higher than the speed

Features DC geared motor  Compact motor drive with a continuous hexagon socket and integrated displacement encoder. The geared motor can be ordered with an idle speed of 115 rpm or 230 rpm. The geared motor serves as a simple upgrade from the manually operated version to the electric motor solution. The motor is supplied with a matching cable. Series 3143.00-1002 3143.00-1003 3143.00-1006 3143.00-1008 Motor operating range 6 - 30 V 6 - 30 V 6 - 30 V 6 - 30 V Motor Nennbereich 18 V 18 V 18 V 18 V Motor nominal range inside 6kt SW6 inside 6kt SW7 inside 6kt SW6 inside 6kt SW7 Gear ratio: 1 gängig 1 gängig 2 gängig 2 gängig Duty cycle 20% (bei 5 Min.) 20% (bei 5 Min.) 20% (bei 5 Min.) 20% (bei 5 Min.) Sensor/Supply Hall/ 5 V DC/ 0,3 A Hall/ 5 V DC/ 0,3 A Hall/ 5 V DC/ 0,3 A Hall/ 5 V DC/ 0,3 A Protection class IP 30 IP 30 IP 30 IP 30 Idle speed 115 U/min 115 U/min 230 U/min 230 U/min max drive torque 5 Nm 5 Nm 5 Nm 5 Nm Rated current 3,3 A bei 5 Nm 3,3 A bei 5 Nm 4,2 A bei 2,8 Nm 4,2 A bei 2,8 Nm Weight: 988 g 987 g 982 g 982 g special features integrated measuring system integrated measuring system integrated measuring system integrated measuring system Motor cable: Included in delivery Included in delivery Included in delivery Included in delivery Complementary articles / spare parts DC gear motor 18V Motor cable 1950mm or 1000mm / with or without invert power/sensors Motor cable 1950mm / with 90° plug Motor cable 1950mm or 1000mm / Compact KTS   zurück zur Übersicht

Nominal torque 5 Nm Idle speed 115 rpm 1 common drive variant Drive inside hexagonal SW 6 or SW7 Features DC geared motor  Compact motor drive with one continuous hexagon socket.The gear motor serves as a simple upgrade from the manually operated variant to the electric motor solution Series 3143.00-1015 3143.00-1041 Motor operating voltage 6 - 30 V 6 - 30 V Motor rated voltage 18 V 18 V Drive: inside 6kt SW6 inside 6kt SW7 Gear number: 1 common 1 common Duty cycle 20% (bei 5 Min.) 20% (bei 5 Min.) Protection class IP 30 IP 30 Idle speed 115 U/min 115 U/min max drive torque 5 Nm 5 Nm Rated current 3,3 A bei 5 Nm 3,3 A bei 5 Nm Weight: 981 g 981 g Motor cable: 2 strands L50mm 2 strands L50mm    Powerful DC motor with worm gear and continuous hexagon socket. The drive was developed for ergonomic table applications, but is also used in many other areas.   Special features DC geared motor Continuous hexagon socket in width across flats SW6 / SW7 Good self-locking properties Can be combined with all Ketterer spindle systems Technical information DC geared motor The working range of the drive (nominal torque) is determined at the service life of 10,000 double strokes. By using a control with short-circuit brake, the holding torque of the drive can be significantly increased.

Powerful  DC motor with worm gear and a continuous internal hexagon. Although the drive was developed for ergonomic table applications, it can be used in many other fields. A cable with AMP plug and an integrated Hall-sensor allows an easy and secure control of the entire system. For extension/spare part the following cables are available in different lengths: Motor cable in 1950mm or 1000mm / with or without invert power/sensors Motor cable in 1950mm / with 90° plug Motor cable in 1950mm or 1000mm / Compact KTS Special features Two integrated Hall-sensors for measurement of the revolutions and direction of rotation Through going hexagon socket in wrench widths 6 mm, 7 mm, 9 mm Available as “power package” or as “high speed” variant 1000 mm motor cable with connector included Good self-locking properties Can be combined with all Ketterer spindle systems Technical notes The drives working range (nominal torque) is determined for a service life of 10.000 double strokes. Through the controller* the system is regulated such that the speed in the entire drive working range is kept as constant as possible. By using a controller with a short-circuit brake the holding torque position of the drive can be increased.* In combination with LogicData control box Compact-3 Model 3143.00-2002 3143.00-2003 3143.00-2012 3143.00-2013 Operating voltage 6 - 30 V 6 - 30 V 6 - 30 V 6 - 30 V Rated voltage 24 V 24 V 24 V 24 V Sensor/Power supply Hall/5 V DC/0,3 A Hall/5 V DC/0,3 A Hall/5 V DC/0,3 A Hall/5 V DC/0,3 A Electric current 5,5 A at 5 Nm 5,5 A at 5 Nm 4,2 A at 2,8 N 4,2 A at 2,8 Nm Protection class IP30 IP30 IP30 IP30 Idle running speed 115 rpm (24 V) 120 rpm* 115 rpm (24 V) 120 rpm* 230 rpm (24 V) 240 rpm* 230 rpm (24 V) 240 rpm* Duty cycle idle speed 20% (at 5 Min.) 20% (at 5 Min.) 20% (at 5 Min.) 20% (at 5 Min.) Rated torque* 5 Nm 5 Nm 2,8 Nm 2,8 Nm Duty cycle nominal load** 20 s ON 240 s OFF 20 s ON 240 s OFF 20 s ON 240 s OFF 20 s ON 240 s OFF Short term peak torque (<1s) 9 Nm 9 Nm 5 Nm 5 Nm Input hex 6mm hex 7mm hex 6mm hex 7mm * In combination with LogicData control box Compact-3 ** Load determined for service life of 10.000 double strokes

Rated torque 3 Nm  Idle speed 150 rpm  Outer dimensions 150x76x40 mm .  Drive inside hexagon SW6/SW7/SW8 Powerful 24 V DC motor with 2-stage worm gear with a continuous internal hexagon on the output. The motor cable with AMP plug and the integrated Hall-sensors allow secure connection and exact positioning of the entire system. The included cable can be ordered here as a spare part. Special features Two integrated Hall-sensors for measurement of the revolutions and direction of rotation Through going hexagon socket in wrench widths 6 mm, 7 mm, 8 mm Good self-locking properties 220 mm + 1750 mm motor cable with connector included Can be combined with most Ketterer spindle systems Technical notes Please note the correct installation position of the drive! The drive is correctly mounted when it turns counterclockwise under load (see installation position/mounting). The drive working range (nominal torque) is determined for a service life of 10.000 double strokes. Through the controller* the system is regulated such that the speed in the entire drive working range is kept as constant as possible. By using a controller with a short-circuit brake the holding torque position of the drive can be increased.* In combination with LogicData control box Compact-3  Model 3121.00-2002 3121.00-2007 3121.00-2008 Motor DC Motor 24 V DC Motor 24 V DC Motor 24 V Sensor/Power supply Hall/5 V DC/0,3 A Hall/5 V DC/0,3 A Hall/5 V DC/0,3 A Protection class IP30 IP30 IP30 Idle running speed 150 rpm (24 V) 150 rpm (24 V) 150 rpm (24 V) Duty cycle idle speed 20% (at 5 min.) 20% (at 5 min.) 20% (at 5 min.) Rated torque* 3 Nm 3 Nm 3 Nm Duty cycle nominal load* 20 s ON 240 s OFF 20 s ON 240 s OFF 20 s ON 240 s OFF Short term peak torque (<1sec) 4,5 Nm 4,5 Nm 4,5 Nm Input hex 6mm hex 7mm hex 8mm *Load determined for service life of 10.000 double strokes

Rated torque 3 Nm  Idle speed 150 rpm  Outer dimensions 150x76x40 mm .  Drive inside hexagonSW7 with brake Powerful 24 V DC motor with 2-stage worm gear with a continuous internal hexagon on the output. The motor cable with AMP plug and the integrated Hall-sensors allow secure connection and exact positioning of the entire system. The included cable can be ordered here as a spare part. Special features Two integrated Hall-sensors for measurement of the revolutions and direction of rotation Through going hexagon socket in wrench widths  7 mm with brake Good self-locking properties 220 mm + 1750 mm motor cable with connector included Can be combined with most Ketterer spindle systems Technical notes Please note the correct installation position of the drive! The drive is correctly mounted when it turns counterclockwise under load (see installation position/mounting). The drive working range (nominal torque) is determined for a service life of 10.000 double strokes. Through the controller* the system is regulated such that the speed in the entire drive working range is kept as constant as possible. By using a controller with a short-circuit brake the holding torque position of the drive can be increased.* In combination with LogicData control box Compact-3  Model 3121.00-2009 Motor DC Motor 24 V Sensor/Power supply Hall/5 V DC/0,3 A Protection class IP30 Idle running speed 150 rpm (24 V) Duty cycle idle speed 20% (at 5 min.) Rated torque* 3 Nm Duty cycle nominal load* 20 s ON 240 s OFF Short term peak torque (<1sec) 4,5 Nm Input hex 7mm *Load determined for service life of 10.000 double strokes

Compact 24 V DC motor with worm gear and continuous internal hexagon. Although the drive was developed for ergonomic table applications, it can be used in many other fields as well. A cable with AMP plug and an integrated Hall-sensor allows an easy and secure control of the entire system.Special featuresTwo integrated Hall-sensors for measurement of the revolutions and direction of rotationContinuous internal hexagon in wrench widths 6 mm, 7 mm, 9 mmGood self-locking propertiesLow noise100 mm + 1750 mm motor cable with connector includedCan be combined with most Ketterer spindle systemsTechnical notesTo ensure secure operation the motor must be operated in the predefined installation position (see installation position/mounting).The drive working range (nominal torque) is determined for a service life of 10,000 double strokes.The connection position of the drive in the entire system with vibration damping elements can be beneficial. However, the functional reliability position of the drive in the application should be tested.Through the controller* the system is regulated such that the speed in the entire drive working range is kept as constant as possible.By using a controller with a short-circuit brake the holding torque position of the drive can be increased.* In combination with LogicData control box Compact-3 Model3133.00-10023133.00-10033133.00-1009Versionwith brakewith brakewith brakeMotorDC Motor 24 VDC Motor 24 VDC Motor 24 VSensor/Power supplyHall/5 V DC/0,3 AHall/5 V DC/0,3 AHall/5 V DC/0,3 AProtection classIP30IP30IP30Idle running speed120 rpm (24 V)120 rpm (24 V)120 rpm (24 V)Duty cycle with idle running20% (at 5 Min.)20% (at 5 Min.)20% (at 5 Min.)Rated torque*2,5 Nm2,5 Nm2,5 NmDuty cycle with 3,5 Nm20 sec ON 4min. OFF20 sec ON 4min. OFF20 sec ON 4min. OFFShort-term peak torque (< 1 sec)5 Nm5 Nm5 NmInputhex 6mmhex 7 mmhex 9 mmModel3133.00-00163133.00-00173133.00-0011Versionwithout brakewithout brakewithout brakeMotorDC Motor 24 VDC Motor 24 VDC Motor 24 VSensor/Power supplyHall/5 V DC/0,3 AHall/5 V DC/0,3 AHall/5 V DC/0,3 AProtection glassIP30IP30IP30Idle running speed120 rpm (24 V)120 rpm (24 V)120 rpm (24 V)Duty cycle with idle running20% (at 5 Min.)20% (at 5 Min.)20% (at 5 Min.)Rated torque*3,5 Nm3,5 Nm3,5 NmDuty cycle with 3,5 Nm*20 sec ON 4min. OFF20 sec ON 4min. OFF20 sec ON 4min. OFFShort-term peak torque (< 1 sec)5 Nm5 Nm5 NmInputhex 6 mmhex 7 mmhex 9 mm* Determined at full load for service life of 10.000 double strokes

Powerful 24 V DC motor with 2-stage worm gear with a continuous internal hexagon on the output. The motor cable with AMP plug and the integrated Hall-sensors allow secure connection and exact positioning of the entire system. The included cable can be ordered here as a spare part.Special featuresTwo integrated Hall-sensors for measurement of the revolutions and direction of rotationThrough going hexagon socket in wrench widths 6 mm, 7 mm, 8 mmGood self-locking properties220 mm + 1750 mm motor cable with connector includedCan be combined with most Ketterer spindle systems Technical notesPlease note the correct installation position of the drive! The drive is correctly mounted when it turns counterclockwise under load (see installation position/mounting).The drive working range (nominal torque) is determined for a service life of 10.000 double strokes.Through the controller* the system is regulated such that the speed in the entire drive working range is kept as constant as possible.By using a controller with a short-circuit brake the holding torque position of the drive can be increased.* In combination with LogicData control box Compact-3  Model3121.00-10023121.00-10033121.00-1004MotorDC Motor 24 VDC Motor 24 VDC Motor 24 VSensor/Power supplyHall/5 V DC/0,3 AHall/5 V DC/0,3 AHall/5 V DC/0,3 AProtection classIP30IP30IP30Idle running speed150 rpm (24 V)150 rpm (24 V)150 rpm (24 V)Duty cycle idle speed20% (at 5 min.)20% (at 5 min.)20% (at 5 min.)Rated torque*2,5 Nm2,5 Nm2,5 NmDuty cycle nominal load*20 s ON 240 s OFF20 s ON 240 s OFF20 s ON 240 s OFFShort term peak torque (<1sec)4,5 Nm4,5 Nm4,5 NmInputhex 6mmhex 7mmhex 8mm * Load determined for service life of 10.000 double strokes

Compact 24 V DC motor with worm gear and a continuous internal hexagon. Optimized sound characteristics due to elastic coupling and vibration damping fastening elements. Although the drive was developed for ergonomic table applications, it can be used in many other fields. The drive is designed and tested for axial pressure load. A cable with AMP plug and an integrated Hall-sensor allows easy and secure control of the entire system. The included cable can be ordered here as a spare part. You can also order the matching spindle unit with motor adapter in our store.Special featuresVibration and sound-damped design through mechanical decoupling of the spindle systemTwo integrated Hall sensors for measurement of the revolutions and direction of rotationThrough going hexagon socket in wrench widths 6 mm and 7 mmGood self-locking properties100 mm + 1750 mm motor cable with connector includedCan be combined with most Ketterer spindle systems Variant keyThe variants are formed by the different wrench widths and by fastening variants with and without fastening plate (Variant A or Variant B).Technical notesThe drive working range (nominal torque) is determined for a service life of 10,000 double strokes.Through the controller* the system is regulated such that the speed in the entire drive working range is kept as constant as possible.By using a controller with a short-circuit brake the holding torque position of the drive can be increased.  * In combination with LogicData control box Compact-3 Model3130.00-1002 Variante B3130.00-1003 Variante B3130.00-2002 Variante A3130.00-2003 Variante AMotorDC Motor 24 VDC Motor 24 VDC Motor 24 VDC Motor 24 VSensor/Power supplyHall/5 V DC/0,3 AHall/5 V DC/0,3 AHall/5 V DC/0,3 AHall/5 V DC/0,3 AProtection classIP30IP30IP30IP30Idle running speed120 rpm (24 V)120 rpm (24 V)120 rpm (24 V)120 rpm (24 V)Duty cycle with idle running20% (at 5 Min.)20% (at 5 Min.)20% (at 5 Min.)20% (at 5 Min.)Rated torque*3,5 Nm3,5 Nm3,5 Nm3,5 NmDuty cycle with 3,5 Nm*20 sec ON 240 sec OFF20 sec ON 240 sec OFF20 sec ON 240 sec OFF20 sec ON 240 sec OFFShort-term peak torque (<1sec)6 Nm6 Nm6 Nm6 NmInputhex 6mmhex 6mmhex 6mmhex 7mm* Determined at full load for service life of 10,000 double strokes

Compact 24 V DC motor with worm gear and a continuous internal hexagon. Although the drive was developed for ergonomic table applications, it can be used in many other fields. A cable with AMP plug and an integrated Hall-sensor allows easy and secure control of the entire system. The included cable can be ordered here as a spare part. You can also order the matching spindle unit with motor adapter in our store.Special featuresTwo integrated Hall-sensors for measurement of the revolutions and direction of rotationThrough going hexagon socket in wrench widths 6 mm and 9 mmGood self-locking propertiesLow noise1000 mm + 1750 mm motor cable with connector includedCan be combined with all Ketterer spindle systems Technical notesThe drive working range (nominal torque) is determined for a service life of 10.000 double strokes.Through the controller* the system is regulated such that the speed in the entire drive working range is kept as constant as possible.By using a controller with a short-circuit brake the holding torque position of the drive can be increased. *In combination with LogicData control box Compact-3 Model3133.48-00093133.48-0016MotorDC Motor 24 VDC Motor 24 VSensor/Power supplyHall/5 V DC/0,3 AHall/5 V DC/0,3 AProtection classIP30IP30Duty cycle idle speed20% (at 5 Min.)20% (at 5 Min.)Idle running speed100 rpm (24 V)100 rpm (24 V)Rated torque*5 Nm5 NmDuty cycle nominal load20 s ON/ 240 s OFF20 s ON/ 240 s OFFShort term peak torque (<1sec)8 Nm8 NmInputhex 9mmhex 6mm * Load determined for service life of 10.000 double strokes

Compact 24 V DC motor with worm gear and continuous internal hexagon. Although the drive was developed for ergonomic table applications, it can be used in many other fields as well. A cable with AMP plug and an integrated Hall-sensor allows an easy and secure control of the entire system. You can find a suitable spindle unit with motor adapter here. Special features Two integrated Hall-sensors for measurement of the revolutions and direction of rotation Continuous internal hexagon in wrench widths 6 mm, 7 mm, 9 mm Good self-locking properties Low noise 100 mm + 1750 mm motor cable with connector included Can be combined with most Ketterer spindle systems Technical notes To ensure secure operation the motor must be operated in the predefined installation position (see installation position/mounting). The drive working range (nominal torque) is determined for a service life of 10,000 double strokes. The connection position of the drive in the entire system with vibration damping elements can be beneficial. However, the functional reliability position of the drive in the application should be tested. Through the controller* the system is regulated such that the speed in the entire drive working range is kept as constant as possible. By using a controller with a short-circuit brake the holding torque position of the drive can be increased. * In combination with LogicData control box Compact-3 Model 3133.00-0002 3133.00-0003 3133.00-0001 Version with brake with brake with brake Motor DC Motor 24 V DC Motor 24 V DC Motor 24 V Sensor/Power supply Hall/5 V DC/0,3 A Hall/5 V DC/0,3 A Hall/5 V DC/0,3 A Protection class IP30 IP30 IP30 Idle running speed 120 rpm (24 V) 120 rpm (24 V) 120 rpm (24 V) Duty cycle with idle running 20% (at 5 Min.) 20% (at 5 Min.) 20% (at 5 Min.) Rated torque* 2,5 Nm 2,5 Nm 2,5 Nm Duty cycle with 3,5 Nm* 20 sec ON 4min. OFF 20 sec ON 4min. OFF 20 sec ON 4min. OFF Short-term peak torque (< 1 sec) 5 Nm 5 Nm 5 Nm Input hex 6mm hex 6 mm hex 6 mm Model 3133.00-0014 3133.00-0010 3133.00-0012 Version without brake without brake without brake Motor DC Motor 24 V DC Motor 24 V DC Motor 24 V Sensor/Power supply Hall/5 V DC/0,3 A Hall/5 V DC/0,3 A Hall/5 V DC/0,3 A Protection glass IP30 IP30 IP30 Idle running speed 120 rpm (24 V) 120 rpm (24 V) 120 rpm (24 V) Duty cycle with idle running 20% (at 5 Min.) 20% (at 5 Min.) 20% (at 5 Min.) Rated torque* 3,5 Nm 3,5 Nm 3,5 Nm Duty cycle with 3,5 Nm* 20 sec ON 4min. OFF 20 sec ON 4min. OFF 20 sec ON 4min. OFF Short-term peak torque (< 1 sec) 5 Nm 5 Nm 5 Nm Input hex 6 mm hex 7 mm hex 9 mm * Determined at full load for service life of 10.000 double strokes

Nominal speed 120rpm l Static pressure load 10,000N l Static tensile load 10,000 N l Maintenance-free l 2 versions selectable Electromotive screen drive - set Electrified drive system consisting of motor, control, spindle and spindle nut. The drive is designed for high tensile and compressive forces. The self-locking system design ensures safe operation. In addition to the drive system, a 1-channel remote control is also included in the set.   Technical data Series 3062 Voltage 230V~/50Hz Current 1,0 A Inrush current (factor) X 1,2 Power motor 220 W Rated torque 5 Nm / Peak torque 7 Nm (kurzzeitig) No-load speed 134 U/min Rated speed 120 U/min bei 5Nm Operating mode 2,5 min on, 45 min off Ambient temperature / humidity  Operation T=-10°C …. +60°C /H max. 90% Storage: T=-15°C….+70°C / dry non-condensing Operating temperature Motor  overheating protection with shutdown at approx. 110°C Protection class IP40 Max. short-time static pressure load 10.000 N Max short-time static tensile load 10.000 N Spindle type 25 x 4 Travel speed at nominal load 8 mm/s Scope of delivery The set includes: 1 x electromotive spindle drive, consisting of the motor incl. control unit 1 x 1-channel remote control 1 x spindle 25 x 4 / 1,5 m long 1 x spindle nut   1 x crank with safety spring for note locking (optional)   Technical notes After shutdown due to overheating min 15 min pause time is necessary

Motorized solution for the individual sit-stand workplace. Stepless height adjustment to customer specific stroke. The included cable can be ordered here as a spare part.Special featuresA sleek design allows the complete inline actuator to be integrated into the tube of a table leg.Simple mountingIntegrated position measuring systemSingle telescopic function Model3120.00-V02EXXXHXXXMotorDC Motor 24 VSensor/Power supplyHall/5 V DC/0,3 AProtection classIP30Duty cycle20% (at 5 Min.)Idle running speed100 rpm (24 V)150 rpm *Stroke max.retracted height -109 mmType of spindleSG14x16P4 RH Max. lifting force800 NMax. drive torque3 NmMovement speed43 mm/s* in combination with LogicData control box Compact-3

Lifting force 600Nm l Travelling speed 48 mm/s l Simple mounting l Installation space requirement 40x63 mm Features Inline spindle drive 3122 100-500mm stroke The electromotive solution for the sit/stand workstation. Infinitely variable height adjustment with customised lifting height. A very slim design enables the complete inline drive to be integrated into the table leg. Special features Inline spindle drive 100-500mm stroke Simple attachment Integrated position measuring system 1-fold telescopic Technical specifications Inline spindle drive 100-500mm stroke Series 3122.00-V01EXXXHXXX Motor DC Motor 24 V Sensor/Power supply Hall/5 V DC/0,3 A Protection class IP30 Duty cycle 20% (at 5 Min.) Idle running speed 180 rpm (24 V) 180 rpm * Stroke max. retracted height -171 mm Type of spindle SG12x16P4 RH ** Max. lifting force 600 N Max. drive torque 2,5 Nm Movement speed 48 mm/s * in conjunction with LogicData control unit Compact-3 ** other spindle types available on request Safety instructions: Depending on the spindle used, the self-locking of the system must be checked.

Idle speed 270 rpm l Traversing speed 12-45 mm/s l For push and pull movements l Powerful 24 V DC motor with worm gear unit Features Motor drive for through-spindle 4778 Powerful 24 V DC motor with worm gear, designed for non-rotating through-spindle for push and pull movements. A cable with AMP connector and integrated Hall sensors allow simple and safe control of the entire system. Special features Two integrated Hall sensors for detecting rotations and the direction of rotation Various types of internal thread for continuous spindle Good self-locking properties Fast and powerful Spindle must be ordered separately Series 4778.00-0002 4778.00-0004 4778.00-0006 Drive motor DC Motor 24 V  DC Motor 24 V  DC Motor 24 V  Sensor / supply Hall/5 V DC/0,3 A Hall/5 V DC/0,3 A Hall/5 V DC/0,3 A Protection class IP30 IP30 IP30 Operating temperature 0° bis +30° 0° bis +30° 0° bis +30° Electric current (IN) at max. load  8 A 8 A 8 A Idle running speed 270 U/min 270 U/min 270 U/min Duty cycle idle speed 20% (bei 5 Min.) 20% (bei 5 Min.) 20% (bei 5 Min.) Duty cycle at max. load 10 s ON 240 s OFF 13 s ON 240 s OFF 8 s ON 240 s OFF Max. lifting force* 1900 N 3700 N 950 N Traverse speed (constant from F= 0 bis Fmax.)** 24mm / s 12 mm / s 45 mm / s Static Self locking *** 200 kg 380 kg 200 kg Output (Inner thread) SG16x8P4 RH Tr16x4 RH SG14x16P4 RH * Determined for service life of 10,000 double strokes** The controller regulates the system in such a way that the travel speed in the entire drive working range is kept as constant as possible*** In combination with controller, which has a short circuit brake Technical information The spindle is not included in the scope of delivery and must be ordered separately Attention: It is essential to observe the correct installation position (see installation example). The drive must be protected against the effects of lateral forces by a separate guide system. The operating range of the drive (rated torque) is determined for a service life of 10,000 double strokes. The holding torque of the drive can be increased by using a control unit with a short-circuit brake.

Installation dimension 589 l Stroke 525 l Lifting force 900 N l Travel 20mm/rev l With and without motor mounting l Travel speed 40mm/s lUniversally applicable lifting unit with a bevel gear head for linear drive solutions. Possible applications are height adjustable tables, various adjustment functions for furniture items as well as all manner of linear adjustment in residential, mobile home or industrial fields.Special featuresIdeal for the drives: 3112.00/ 3133.00 / 3133.48 / 3130.00Available in customized spindle lengthsSimple mountingConnection to the drive hex 9 mmModel3130.14-V01EXXXHXXX 3130.14-V02EXXXHXXXType of spindleSG14x20P4 RHTravel path20 mm/rotationTraverse speed*40 mm/s*Max. strokeretracted length -64 mmMax. lifting force900 NRequired drive torque3,5 Nm * In combination with motor 3133 and LogicData control box Compact-3Technical notesThe lifting units must be protected against lateral forces by a separate guide system.Attention: The spindle systems with a spindle pitch > 3mm may not be self-locking. Check the self-locking effect in the application. The lifting unit is only pressure loadable.Incorrect dimensioning of the guide system can damage the lifting unit: Please note the design and safety instructions for spindle drives. You will find them at: https://www.ketterer.de/en/downloads/instructions

2 Varianten zur Auswahl  l  Hub 720 mm  l  Hubkraft 900 N  l  Verfahrweg 40mm/s  l Maximaler Hub bei minimalem EinbaumaßTwofold telescopic lifting unit with bevel gear head for various linear drive solutions. Ideal for electromotive sit-stand workplace applications or wherever an infinite linear adjustment is required at a high speed, maximum stroke with a minimum installation dimension.Special featuresDouble speed through synchronous telescope designMaximum stroke with minimum installation dimensionIdeal for electromotive drivesTechnical notesThe lifting units must be protected against lateral forces by a separate guide system.Attention: The spindle systems with a spindle pitch > 3mm may not be self-locking. Check the self-locking effect in the application.The lifting unit is only pressure loadable.Incorrect dimensioning of the guide system can damage the lifting unit: Please note the design and safety instructions for spindle drives. You will find them at: https://www.ketterer.de/en/downloads/instructionBaureihe4115.14-V01E500M4904115.14-V02E495M484Type of spindleSG20x10P2 RH SG10x10P2 RHSG20x10P2 RH SG10x10P2 RHTravel path20 mm/rotation synchronous spindle movement20 mm/rotation synchronous spindle movementTraverse speed*40 mm/s*40 mm/s*Retracted length E500 mm495 mmCentral tube connection M490 mm484 mmEnginge mountnoyesStroke H**720 mm720 mmMax. lifting forcedyn. 900 N stat. 900 Ndyn. 900 N stat. 900 NRequired drive torque3,3 Nm3,3 Nm* In combination with motor 3133 and the LogicData controll box Compact-3** Stroke length of 720 mm is constant at installation dimension between 476 mm and 560 mm