TR 20 round nuts with trapezoidal thread POM
€28.37*
SG 20x10 P2 l right-hand thread l five-start l outer diameter 36mm l length 32mm l POM l based on DIN 380Properties Round nut with trapezoidal thread SG 20 POM
Our trapezoidal leadscrew nuts have a right-hand motion thread. This is multi-start and is suitable for combination with our steel or aluminum spindle tubes. The spindle nut with trapezoidal thread is made of POM (plastic). This gives the round nut good sliding and wear properties. In addition, high heat resistance and dimensional stability can be counted among its properties. With a nominal thread size of 25mm, two different thread designs can be selected:
SG 20x10 P2 (Thread pitch 10mm P2 l five-start - right-hand thread)
The trapezoidal threads of the round nuts are listed as special threads (SG). These are based on standard 380 and meet requirements outside the standard. The trapezoidal thread nut made of POM is produced by machining. Excess material is removed mechanically in the form of chips. This allows high demands on accuracy and surface quality to be met.
13900.20-06
Thread
SG 20x10 P2 right-hand threadfive-start based on DIN 380
Dimensions
Outer diameter d1: 36mm Length a: 32mmchamfer outside f1/f2: 1x45°.Tolerance field: 7H
Material
POM
Matching spindle
Spindle tube in aluminum
Application Round nut with trapezoidal thread SG 20 POM
The trapezoidal lead screw nut forms a drive solution in combination with our trapezoidal lead screws. This unit is used for the transmission of large axial forces and the conversion of rotating movements into linear ones. The system of spindle and nut is self-locking and usually requires no additional locking when at rest. By matching the nuts to the spindles, running noise and smoothness can be optimized. This enables application even in noise-sensitive areas.
Ketterer Antriebe supplies trapezoidal lead screw nuts for all trapezoidal lead screw spindles from stock. In addition to our POM version, discover other round nuts in brass and round nuts in PA6-GF30 as well as our selection in different shapes:
Flange nut with trapezoidal thread in POM or brass
square nut with trapezoidal thread in POM
You would like to combine your nut with a suitable spindle? Then it is worth taking a look at our range of spindles:
Trapezoidal thread spindle in steel or stainless steel
Spindle tubes with trapezoidal thread in steel or aluminum
For further information on round nuts with trapezoidal thread, please refer to the downloads listed below.
Back to the overview
TR 25 round nuts with trapezoidal thread POM
€29.74*
SG 25 l 3 versions to choose from l Right-hand thread l Outer diameter 48mm l Length 42mm l POM l Based on DIN 380Properties Round nut with trapezoidal thread SG 25 POM
Our trapezoidal leadscrew nuts have a right-hand motion thread. This is multi-start and is suitable for combination with our steel or aluminum spindle tubes. The spindle nut with trapezoidal thread is made of POM (plastic). This gives the round nut good sliding and wear properties. In addition, high heat resistance and dimensional stability can be counted among its properties. With a nominal thread size of 25mm, two different thread designs can be selected:
SG 25x7 P3,5 (Thread pitch 7mm P3.5 l double thread - right hand thread)
SG 25x12 P6 (Thread pitch 12mm P6 l double thread - right hand thread)
SG25x100 P4 ( Thread pitch 100mmP4 l twenty-five thread - right hand thread)
The trapezoidal threads of the round nuts are listed as special threads (SG). These are based on standard 380 and meet requirements outside the standard. The trapezoidal thread nut made of POM is produced by machining. Excess material is removed mechanically in the form of chips. This allows high demands on accuracy and surface quality to be met.
13603.20-06
13602.20-06
13700.20-04
Thread
SG 25x7 P3,5Right-hand threadtwo-course
based on DIN 380
SG 25x7 P3,5Right-hand threadtwo-course
based on DIN 380
SG 25x100 P4Right-hand thread
twenty-five-course
based on DIN 380
Dimensions
Outer diameter d1: 48mm Length a: 42mmChamfer outside f1/f2: 1x45°Tolerance field: 7H
Außendurchmesser d1: 48mmLänge a: 42mmFase außen f1/f2: 1x45°Toleranzfeld: 7H
Außendurchmesser d1: 48mmLänge a: 42mmFase außen f1/f2: 1x45°Toleranzfeld: 7H
Material
POM
POM
POM
Matching spindle
Spindelrohr in Stahl Spindelrohr in Aluminium
Spindelrohr in Aluminium
Application Round nut with trapezoidal thread SG 25 POM
The trapezoidal lead screw nut forms a drive solution in combination with our trapezoidal lead screws. This unit is used for the transmission of large axial forces and the conversion of rotating movements into linear ones. The system of spindle and nut is self-locking and usually requires no additional locking when at rest. By matching the nuts to the spindles, running noise and smoothness can be optimized. This enables application even in noise-sensitive areas.
Ketterer Antriebe supplies trapezoidal thread nuts for all trapezoidal thread spindles from stock. In addition to our POM version, discover other round nuts in brass and round nuts in PA6-GF30 as well as our selection in different shapes:
Flanged nut with trapezoidal thread in POM or brass
Square nut with trapezoidal thread in POM
You would like to combine your nut with a matching spindle? Then it's worth taking a look at our spindle range:
Trapezoidal thread spindle in steel or stainless steel
Stem tubes with trapezoidal thread in steel or aluminum
For more information on the round nuts with trapezoidal thread, please refer to the downloads listed below.
Back to the overview